A:
Operating current = operating voltage / coil resistance; rated current = rated voltage / coil resistance.
A:
(1) Hot or soaking cleaning is not allowed.
(2) Please only brush the soldering surface of the printed board.
(1) Hot or soaking cleaning is allowed.
(2) Please use alcohol or water cleaning solution.
(3) The cleaning temperature should be controlled below 40 °C.
(4) Please do not USE ultrasonic cleaning or cut off the terminal of the relay, otherwise the coil will be disconnected and the contacts will be bonded.
Plastic sealed type relays after being mounted on the PCB and welded may be damaged due to different welding conditions of users. Therefore, if the relay needs to be cleaned after welding, please adopt our recommendation for welding and selecting a special sealed product. Do not use freon, trichloroethane, thinner diluent or benzine gasoline for cleaning.
A:
Operating current = operating voltage / coil resistance; rated current = rated voltage / coil resistance.
A:
(1) Hot or soaking cleaning is not allowed.
(2) Please only brush the soldering surface of the printed board.
(1) Hot or soaking cleaning is allowed.
(2) Please use alcohol or water cleaning solution.
(3) The cleaning temperature should be controlled below 40 °C.
(4) Please do not USE ultrasonic cleaning or cut off the terminal of the relay, otherwise the coil will be disconnected and the contacts will be bonded.
Plastic sealed type relays after being mounted on the PCB and welded may be damaged due to different welding conditions of users. Therefore, if the relay needs to be cleaned after welding, please adopt our recommendation for welding and selecting a special sealed product. Do not use freon, trichloroethane, thinner diluent or benzine gasoline for cleaning.
A:
Operating current = operating voltage / coil resistance; rated current = rated voltage / coil resistance.
A:
(1) Hot or soaking cleaning is not allowed.
(2) Please only brush the soldering surface of the printed board.
(1) Hot or soaking cleaning is allowed.
(2) Please use alcohol or water cleaning solution.
(3) The cleaning temperature should be controlled below 40 °C.
(4) Please do not USE ultrasonic cleaning or cut off the terminal of the relay, otherwise the coil will be disconnected and the contacts will be bonded.
Plastic sealed type relays after being mounted on the PCB and welded may be damaged due to different welding conditions of users. Therefore, if the relay needs to be cleaned after welding, please adopt our recommendation for welding and selecting a special sealed product. Do not use freon, trichloroethane, thinner diluent or benzine gasoline for cleaning.
A:
Operating current = operating voltage / coil resistance; rated current = rated voltage / coil resistance.
A:
(1) Hot or soaking cleaning is not allowed.
(2) Please only brush the soldering surface of the printed board.
(1) Hot or soaking cleaning is allowed.
(2) Please use alcohol or water cleaning solution.
(3) The cleaning temperature should be controlled below 40 °C.
(4) Please do not USE ultrasonic cleaning or cut off the terminal of the relay, otherwise the coil will be disconnected and the contacts will be bonded.
Plastic sealed type relays after being mounted on the PCB and welded may be damaged due to different welding conditions of users. Therefore, if the relay needs to be cleaned after welding, please adopt our recommendation for welding and selecting a special sealed product. Do not use freon, trichloroethane, thinner diluent or benzine gasoline for cleaning.
A:
Operating current = operating voltage / coil resistance; rated current = rated voltage / coil resistance.
A:
(1) Hot or soaking cleaning is not allowed.
(2) Please only brush the soldering surface of the printed board.
(1) Hot or soaking cleaning is allowed.
(2) Please use alcohol or water cleaning solution.
(3) The cleaning temperature should be controlled below 40 °C.
(4) Please do not USE ultrasonic cleaning or cut off the terminal of the relay, otherwise the coil will be disconnected and the contacts will be bonded.
Plastic sealed type relays after being mounted on the PCB and welded may be damaged due to different welding conditions of users. Therefore, if the relay needs to be cleaned after welding, please adopt our recommendation for welding and selecting a special sealed product. Do not use freon, trichloroethane, thinner diluent or benzine gasoline for cleaning.
A:
Operating current = operating voltage / coil resistance; rated current = rated voltage / coil resistance.
A:
(1) Hot or soaking cleaning is not allowed.
(2) Please only brush the soldering surface of the printed board.
(1) Hot or soaking cleaning is allowed.
(2) Please use alcohol or water cleaning solution.
(3) The cleaning temperature should be controlled below 40 °C.
(4) Please do not USE ultrasonic cleaning or cut off the terminal of the relay, otherwise the coil will be disconnected and the contacts will be bonded.
Plastic sealed type relays after being mounted on the PCB and welded may be damaged due to different welding conditions of users. Therefore, if the relay needs to be cleaned after welding, please adopt our recommendation for welding and selecting a special sealed product. Do not use freon, trichloroethane, thinner diluent or benzine gasoline for cleaning.
A:
Operating current = operating voltage / coil resistance; rated current = rated voltage / coil resistance.
A:
(1) Hot or soaking cleaning is not allowed.
(2) Please only brush the soldering surface of the printed board.
(1) Hot or soaking cleaning is allowed.
(2) Please use alcohol or water cleaning solution.
(3) The cleaning temperature should be controlled below 40 °C.
(4) Please do not USE ultrasonic cleaning or cut off the terminal of the relay, otherwise the coil will be disconnected and the contacts will be bonded.
Plastic sealed type relays after being mounted on the PCB and welded may be damaged due to different welding conditions of users. Therefore, if the relay needs to be cleaned after welding, please adopt our recommendation for welding and selecting a special sealed product. Do not use freon, trichloroethane, thinner diluent or benzine gasoline for cleaning.
A:
Operating current = operating voltage / coil resistance; rated current = rated voltage / coil resistance.
A:
(1) Hot or soaking cleaning is not allowed.
(2) Please only brush the soldering surface of the printed board.
(1) Hot or soaking cleaning is allowed.
(2) Please use alcohol or water cleaning solution.
(3) The cleaning temperature should be controlled below 40 °C.
(4) Please do not USE ultrasonic cleaning or cut off the terminal of the relay, otherwise the coil will be disconnected and the contacts will be bonded.
Plastic sealed type relays after being mounted on the PCB and welded may be damaged due to different welding conditions of users. Therefore, if the relay needs to be cleaned after welding, please adopt our recommendation for welding and selecting a special sealed product. Do not use freon, trichloroethane, thinner diluent or benzine gasoline for cleaning.
